Tab Content
  • Jabes's Avatar
    05-07-2019, 05:23 AM
    This also works for me on my Qotom box. It'd be nice to see these brought through into the system information alongside cpu, memory etc.
    4 replies | 4820 view(s)
  • Jabes's Avatar
    05-07-2019, 03:28 AM
    Jabes started a thread Change SSH port in Networking
    Is there a way through the interface of changing the SSH port, or should I just change sshd_config? I've already locked down my access rules to only...
    3 replies | 65 view(s)
  • Jabes's Avatar
    05-07-2019, 02:50 AM
    Jabes replied to a thread High CPU - demdgbscfd in Installation
    This looks like the XORDDos trojan - https://superuser.com/questions/877896/unknown-linux-process-with-random-command And likely caused by a...
    5 replies | 130 view(s)
  • Jabes's Avatar
    05-06-2019, 03:42 PM
    I think this is a Trojan on the box, have pulled it and swapped in my old router while restore the configuration
    4 replies | 107 view(s)
  • Jabes's Avatar
    05-06-2019, 03:07 PM
    Jabes replied to a thread High CPU - demdgbscfd in Installation
    I did have SSH enabled, only from local network I thought. I killed the process and it has come back under a different name I will pull the box. ...
    5 replies | 130 view(s)
  • Jabes's Avatar
    05-06-2019, 02:46 PM
    Something odd is going on, I don't understand. If I watch tcpdump on what I think is traffic originating from my untangle box, I see a lot of...
    4 replies | 107 view(s)
  • Jabes's Avatar
    05-06-2019, 12:52 PM
    Using conntrack -L - looks like my conntrack table is full of entries like this - SYN_SENT UNREPLIED tcp 6 88 SYN_SENT src=121.198.136.40...
    4 replies | 107 view(s)
  • Jabes's Avatar
    05-06-2019, 12:25 PM
    May 6 20:23:55 untangle kernel: nf_conntrack: nf_conntrack: table full, dropping packet May 6 20:23:55 untangle kernel: nf_conntrack:...
    4 replies | 107 view(s)
  • Jabes's Avatar
    05-06-2019, 11:32 AM
    Suddenly getting quite high cpu usage from demdgbscfd - and I can't find any reference to this binary using google. What is it for? Anything I...
    5 replies | 130 view(s)
  • Jabes's Avatar
    04-30-2019, 10:29 PM
    Jabes replied to a thread Unifi, USG, Bridge mode in Networking
    Hi: I couldn't get the routing from the USG to the controller to work, so I reset the untangle configuration and configured as a router without...
    6 replies | 210 view(s)
  • Jabes's Avatar
    04-30-2019, 09:00 AM
    Jabes replied to a thread Unifi, USG, Bridge mode in Networking
    I bought the equipment I've installed untangle on because I intended that ultimately it will replace the USG. Just to start with I wanted to get used...
    6 replies | 210 view(s)
  • Jabes's Avatar
    04-29-2019, 10:28 PM
    Jabes replied to a thread Unifi, USG, Bridge mode in Networking
    Thanks for replying. I've configured WAN balancer, and the source routing is working fine for things inside the various VLANs talking to the correct...
    6 replies | 210 view(s)
  • Jabes's Avatar
    04-29-2019, 02:15 PM
    Hi: I am new to untangle but can normally find my way around networking equipment. I have installed Untangle behind a Ubiquiti USG with two...
    6 replies | 210 view(s)
No More Results
About Jabes

Basic Information

About Jabes
URLs submitted:
0

Statistics


Total Posts
Total Posts
13
Posts Per Day
0.47
General Information
Last Activity
05-22-2019 02:20 PM
Join Date
04-29-2019
Referrals
0

SEO by vBSEO 3.6.0 PL2