Search:

Type: Posts; User: Archness

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. I'll look at doing it this weekend. I think...

    I'll look at doing it this weekend.

    I think I'll need about 2-3 hours to clone the disk over.
  2. I've been avoiding the SSD since the DB writes...

    I've been avoiding the SSD since the DB writes tend to be a little rough on that. I also have some PTSD from the first line of UT appliances with SSD that burned out early.
  3. Extremely high CPU during daily report generation

    I am seeing very high cpu load during report generation that is causing connections and sessions to drop while the reports are generated.

    Is it possible to set the report generation activities...
  4. Replies
    1
    Views
    2,030

    e3w use wireless as WAN connection

    Hi,

    Is it possible on the e3w to use the wireless as a WAN connection or add a USB WLAN card (alpha card) to the router and use that as a WAN uplink? I'm thinking for backup connections or travel...
  5. Replies
    20
    Views
    948

    What happened?

    What happened?
  6. Replies
    20
    Views
    948

    Hence the supermicro board in the other post. I...

    Hence the supermicro board in the other post. I always figured 10G would require upgrades.
  7. Replies
    20
    Views
    948

    Yeah, I do also want to move to 10G for the L3...

    Yeah, I do also want to move to 10G for the L3 device as I am doing more things with it.

    I double checked the PCI-E spec and it should be fine. I ordered Intel NICs tonight and will try them...
  8. Looking to upgrade UT to: SUPERMICRO MBD-X10SAE-O ATX

    Here is the link to the Mobo: https://www.supermicro.com/en/products/motherboard/X10SAE

    Based on the issue I am having with dropped packets due to PCI Bus limitations, I am looking at upgrading my...
  9. Replies
    20
    Views
    948

    I've been looking at adding some more VM hosts...

    I've been looking at adding some more VM hosts and potentially virtualizing Untangle on them based on previous advice from Sky-knight to use VMware for 10G or higher due to NIC support.

    I found a...
  10. Replies
    20
    Views
    948

    Yeah, I'm going to go ahead and agree with you on...

    Yeah, I'm going to go ahead and agree with you on that.

    Motherboard Link: https://ark.intel.com/content/www/us/en/ark/products/51857/intel-desktop-board-dh61cr.html
  11. Replies
    20
    Views
    948

    Thank you for the responses. Some very good...

    Thank you for the responses. Some very good reminders and insights.

    UT Hardware List

    CPU: Intel(R) Core(TM) i7-2600K CPU @ 3.40GHz
    RAM: 2x4GB DDR3 1333Mhz
    MOBO: Intel Classic DH61CR Desktop...
  12. Replies
    20
    Views
    948

    11 VLANs beyond the LAN (VLAN1) and 36 devices on...

    11 VLANs beyond the LAN (VLAN1) and 36 devices on that switch. 5 XEN hosts, 2 NAS, Camera Uplink, 3 Access Switches, Total network clients across VMs, Servers, endpoints, etc. comes to ~70.
    ...
  13. Replies
    20
    Views
    948

    Potential packet loss/ DHCP latency

    Hi,

    I doubt this issue is untangle but I'm working backwards through everything to try and isolate it rather than guess.

    I have multiple VLANs setup in my network, some are physical separation...
  14. Replies
    0
    Views
    459

    UT support for Turris MOX?

    Hi,

    I was wondering if UT was considering supporting the Turris MOX when it comes out?

    https://www.indiegogo.com/projects/turris-mox-modular-open-source-router-security-computers#/
  15. Maximum speed via TunnelVPN on WRT1900ACS

    Hi Everyone,

    I was wondering if anyone has done testing and tracking of the max speed via the Tunnel VPN on the firmware version of UT.

    My testing is below:

    HQ/DC: 1Gbps duplex

    Remote...
  16. Replies
    40
    Views
    9,428

    I saw the traffic tags for routing traffic to the...

    I saw the traffic tags for routing traffic to the tunnel interface or not, is this going to be expanded later to support more dynamic routing?
  17. Replies
    2
    Views
    1,759

    The only reason I thought that aggregated reports...

    The only reason I thought that aggregated reports in CMD might be a bit heavy is due the amount of data. My UTs alone generate over 600GB a year.

    Thanks for the info though.
  18. Replies
    2
    Views
    1,759

    Central Reports Server

    Hi,

    I have been deploying multiple UT appliances and I would like the ability to centralize the report generation for my extended environment.

    Is there an option to do this that doesn't...
  19. Ok, Thanks for the info. Is there a way to...

    Ok, Thanks for the info.


    Is there a way to do it with IPsec? This is fairly critical the long term business roll out.

    I also found this doc for how to make it work with PFsense. Fully...
  20. Use Main Office as gateway for all internet traffic

    Hi,

    I've got a main office with a remote office. The group I'm setting this up for wants to route all of the internet traffic for remote offices through the main office.



    The Main Office...
  21. Thanks guys.

    Thanks guys.
  22. I made it a /20 which shpuld be 16 class C. so...

    I made it a /20 which shpuld be 16 class C. so that should work.

    thanks
  23. So, in the DHCP settings, I just set the range to...

    So, in the DHCP settings, I just set the range to 10.10.0.5 - 10.10.16.200 ? Would that work?
  24. Awesome, Thanks guys. Just wanted to make sure...

    Awesome, Thanks guys. Just wanted to make sure the DHCP server would handle a larger subnet.
  25. Increasing the subnet size for the DHCP server in Untangle

    I have a Untangle box (community Edition) running as a firewall on my campus public wifi. Its just acting as a router/firewall/network filter.

    Network Map

    I would like to replace all of the...
Results 1 to 25 of 50
Page 1 of 2 1 2

SEO by vBSEO 3.6.0 PL2