Search:

Type: Posts; User: bjmohr

Search: Search took 0.01 seconds.

  1. [edit - while at work I looked up the u25 product...

    [edit - while at work I looked up the u25 product page - I had the USB thumb drive stuck in the back next to the network ports which should be the usb 3.0 compatible port. Keyboard was plugged into...
  2. Indeed I was using a 3.0 USB thumb drive for the...

    Indeed I was using a 3.0 USB thumb drive for the image... On the night when I first attempted the clean install (following the update going south..) I was pushing 2am so to your point I honestly...
  3. I have emailed a support request... Alas, I'm a...

    I have emailed a support request... Alas, I'm a home subscriber so I'm low on the totem pole. On a closer reading I think of the usb boot instructions, I think my problem may be 64 vs 32 bit for the...
  4. attempting update to 14.0.1 - key combo to get u25 to boot from USB?

    Hello, I have seem to have a failed upgrade from 13.2.1 to 14.0.1 on a u25 appliance. It is stuck on "service unavailable" in the web gui. Direct attached monitor eventually shows the untangle...
  5. Replies
    5
    Views
    2,457

    I had a similar experience... dead u25 and a...

    I had a similar experience... dead u25 and a replacement u25 I needed to restore a backup configuration file on to. Couldn’t see a way to do it via Command center (could see the backups linked to the...
  6. Replies
    7
    Views
    3,714

    I run eero in bridge mode and they’ve worked out...

    I run eero in bridge mode and they’ve worked out great.


    Sent from my iPhone using Tapatalk
  7. fixed!

    fixed!
  8. Support confirmed on the event widget - and...

    Support confirmed on the event widget - and development fix in the works. If I had to weigh if against access to tunnelVPN and OAuth for captive portal, I'm still satisfied with being on the early...
  9. Opened up a ticket and the good folks at support...

    Opened up a ticket and the good folks at support have been able to restore most widgets, and are looking into the last hold out. As an aside, I have to say the support team have been exceptional....
  10. "Exception!" message at the dashboard - widgets are blank

    I'm very new to untangled so I thought I'd ask the community on this one... Not sure where to start to address this issue. I'm seeing a brief pop up message: "Exception! Message: null is not an...
  11. Replies
    7
    Views
    2,575

    8183 Ended up with this wall mount... works...

    8183
    Ended up with this wall mount... works nicely, but overpriced for what it is - had a moment of weakness on amazon before hitting up the local hardware store for zip tie anchors.
  12. Replies
    7
    Views
    2,575

    Thanks- odd about the threaded holes on the...

    Thanks- odd about the threaded holes on the bottom - deminsions don't line up with vesa standards so I thought there was a chance an OEM bracket existed. Guess they're the "appendix" of the u25
  13. Replies
    7
    Views
    2,575

    I'd be up for it, but the wife would freak if a...

    I'd be up for it, but the wife would freak if a 3D printer showed up on the credit card... time for low tech zip-tie anchors and a happy marriage!
  14. Replies
    7
    Views
    2,575

    wall mount options for u25 appliance

    Is there a preferred wall mount option for the u25 appliance? I can see 4 small threaded holes on the underside - any mounting plate offered by untangle or a partner?
Results 1 to 14 of 14

SEO by vBSEO 3.6.0 PL2